Glasfaserkabel
A/I-DQ(ZN)H
Glasfaserkabel
Loose tube construction, metal-free, longitudinally watertight, halogen-free, flame retardant
Suited for indoor and outdoor use - for Metro, Access or FTTx implementations and and for blowing in into mini pipe systems
Application
- FRP-central element (as strength member)
- jelly-filled loose tubes, SZ-cabling (if necessary with fillers)
- swellable aramid yarns (dry cable core)
- FRNC-outer sheath (0,5 mm) according to IEC 60332-2, UV-resistant, black
Fiber / tube colors
PENGG KABEL standard according to “Color codes – Fiber optic cables” in the document “General information” in the download area.
Upon customer request we can also manufacture according to other color codes (DIN, TIA / EIA-598 (MPO), IEC).
Standard marking
PENGG KABEL – cable type – fiber count/type – ID number – CPR class CE-marking – meter
On request
- FRNC-sheath according to IEC 60332-3
- other sheath color
- other marking
This data sheet describes a standard type.
Numerous variants are available on request.
| tube diameter mm |
number of tubes | max. fibers / tube | max. number of fibers | tensile strength approx. N |
weight approx. kg/km |
outer diameter approx. mm |
fire load MJ/m |
|---|---|---|---|---|---|---|---|
| 1,5 1,5 1,5 1,7 2,1 |
6* 8 12 6* 6* |
12 12 12 12 24 |
72 96 144 72 144 |
700 700 700 900 900 |
38 50 70 45 75 |
5,8 6,7 8,7 6,6 8,2 |
1 1 1 1 2 |
* at lower number of tubes corresponding blind elements are used
Technical data
according to IEC EN 60794-5 – Microduct cabling for installation by blowing
| tensile strength | see above table |
| compressive strength (crush) | 900 N/10 cm |
| impact | 5 Nm (3 impacts, 300 mm hammer radius) |
| torsion | 5 cycles ±360° |
| kink, cable | The cable do not form a kink when a loop is drawn together to a diameter 12 times the cable outer diameter. |
| min. bending radius | R = 20 x D (cable outer diameter) |
| temperature range | storage and transport: -30°C up to +60°C installation1): -5°C up to +50°C operation: -30°C up to +60°C |
| water penetration | No water on free end. |
1) Cable installation by using the cable blowing technology we recommend the following points to consider:
- During unreeling the cable from the drum (coil, ring) twists and kinks must be avoided.
- The indicated bending radii must not be undershot under any circumstances.
- The cable must be protected 24 hours before installation of direct sunlight or bad weather conditions and have to be stored at an ambient temperature of max. 25°C.
- The cable must be clean and dry at the blowing-in process.
- Pipe and cable diameter must be coordinated.
- The optimal ambient temperature during blowing-in is +5°C to +20°C.
Subject to technical alterations.
Application
- FRP-central element (as strength member)
- jelly-filled loose tubes, SZ-cabling (if necessary with fillers)
- swellable aramid yarns (dry cable core)
- FRNC-outer sheath (0,5 mm) according to IEC 60332-2, UV-resistant, black
Fiber / tube colors
PENGG KABEL standard according to “Color codes – Fiber optic cables” in the document “General information” in the download area.
Upon customer request we can also manufacture according to other color codes (DIN, TIA / EIA-598 (MPO), IEC).
Standard marking
PENGG KABEL – cable type – fiber count/type – ID number – CPR class CE-marking – meter
On request
- FRNC-sheath according to IEC 60332-3
- other sheath color
- other marking
This data sheet describes a standard type.
Numerous variants are available on request.
